View ADF4001_162006.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

a
FEATURES 200 MHz Bandwidth 2.7 V to 5.5 V Power Supply Separate Charge Pump Supply (VP) Allows Extended Tuning Voltage in 5 V Systems Programmable Charge Pump Currents 3-Wire Serial Interface Hardware and Software Power-Down Mode Analog and Digital Lock Detect Hardware-Compatible to the ADF4110/ADF4111/ ADF4112/ADF4113 Typical Operating Current 4.5 mA Ultralow Phase Noise 16-Lead TSSOP 20-Lead Chip Scale Package APPLICATIONS Clock Generation Low Frequency PLLs Low Jitter Clock Source Clock Smoothing Frequency Translation SONET, ATM, ADM, DSLAM, SDM
200 MHz Clock Generator PLL ADF4001
GENERAL DESCRIPTION
The ADF4001 clock generator can be used to implement clock sources for PLLs that require very low noise, stable reference signals. It consists of a low-noise digital PFD (Phase Frequency Detector), a precision charge pump, a programmable reference divider, and a programmable 13-bit N counter. In addition, the 14-bit reference counter (R Counter) allows selectable REFIN frequencies at the PFD input. A complete PLL (Phase-Locked Loop) can be implemented if the synthesizer is used with an external loop filter and VCO (Voltage Controlled Oscillator) or VCXO (Voltage Controlled Crystal Oscillator). The N min value of 1 allows flexibility in clock generation.
FUNCTIONAL BLOCK DIAGRAM
AVDD DVDD VP CPGND RSET
ADF4001
REFIN 14-BIT R COUNTER 14 R COUNTER LATCH CLK DATA LE SDOUT 24-BIT INPUT REGISTER 22 FUNCTION LATCH LOCK DETECT
REFERENCE
PHASE FREQUENCY DETECTOR
CHARGE PUMP
CP
CURRENT SETTING 1
CURRENT SETTING 2
CPI3 CPI2
CPI1 CPI6 CPI5
CPI4
N COUNTER LATCH 13 AVDD MUX 13-BIT N COUNTER SDOUT HIGH Z MUXOUT
RFINA RFINB
M3 CE AGND DGND
M2
M1
REV. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 2001
10%, 5 V 10%; AVDD VP 6.0 V ; AGND = DGND = DD = DVDD = 3 V CPGND = 0 V; RSET = 4.7 k ; TA = TMIN to TMAX unless otherwise noted; dBm referred to 50 )
Parameter RF CHARACTERISTICS (3 V) RF Input Frequency RF Input Sensitivity RF CHARACTERISTICS (5 V) RF Input Frequency REFIN CHARACTERISTICS REFIN Input Frequency REFIN Input Sensitivity2 REFIN Input Capacitance REFIN Input Current PHASE DETECTOR Phase Detector Frequency3 CHARGE PUMP ICP Sink/Source High Value Low Value Absolute Accuracy RSET Range ICP Three-State Leakage Current Sink and Source Current Matching ICP vs. VCP ICP vs. Temperature LOGIC INPUTS VINH, Input High Voltage VINL, Input Low Voltage IINH/IINL, Input Current CIN, Input Capacitance LOGIC OUTPUTS VOH, Output High Voltage VOL, Output Low Voltage POWER SUPPLIES AVDD DVDD VP IDD4 (AIDD + DIDD) ADF4001 IP Low Power Sleep Mode NOISE CHARACTERISTICS ADF4001 Phase Noise Floor5 Phase Noise Performance6 200 MHz Output7 Spurious Signals 200 MHz Output7 B Version 5/165 -10/0 10/200 20/200 5/100 -5 10 100 55 Unit MHz min/max dBm min/max MHz min/max MHz min/max MHz min/max dBm min pF max A max MHz max Programmable: See Table V With RSET = 4.7 k With RSET = 4.7 k See Table V 0.5 V VCP VP - 0.5 0.5 V VCP VP - 0.5 VCP = VP/2 -5/0 dBm min/max -10/0 dBm min/max See Figure 2 for Input Circuit For f < 5 MHz, Use DC-Coupled Square Wave (0 to VDD) AC-Coupled. When DC-Coupled: 0 to VDD max (CMOS-Compatible) Test Conditions/Comments See Figure 3 for Input Circuit
ADF4001-SPECIFICATIONS1 (AV
5 625 2.5 2.7/10 1 2 1.5 2 0.8 x DVDD 0.2 x DVDD 1 10 DVDD - 0.4 0.4 2.7/5.5 AVDD AVDD/6.0 5.5 0.4 1 -161 -153 -99 -90/-95
mA typ A typ % typ k typ nA typ % typ % typ % typ V min V max A max pF max V min V max V min/V max V min/V max mA max mA max A typ dBc/Hz typ dBc/Hz typ dBc/Hz typ dBc typ/dBc typ
IOH = 500 A IOL = 500 A
AVDD VP 6.0 V 4.5 mA typical TA = 25C
@ 200 kHz PFD Frequency @ 1 MHz PFD Frequency @ VCXO Output @ 1 kHz Offset and 200 kHz PFD Frequency @ 200 kHz/400 kHz and 200 kHz PFD Frequency
NOTES 1 Operating temperature range is as follows: B Version: -40C to +85C. 2 AVDD = DVDD = 3 V; for AVDD = DVDD = 5 V, use CMOS-compatible levels. 3 Guaranteed by design. Sample tested to ensure compliance. 4 TA = 25C; AVDD = DVDD = 3 V; RFIN = 100 MHz. 5 The synthesizer phase noise floor is estimated by measuring the in-band phase noise at the output of the VCO and subtracting 20 logN (where N is the N divider value). 6 The phase noise is measured with the EVAL-ADF4001EB1 Evaluation Board and the HP8562E Spectrum Analyzer. 7 fREFIN = 10 MHz; f PFD = 200 kHz; Offset frequency = 1 kHz; f RF = 200 MHz; N = 1000; Loop B/W = 20 kHz. Specifications subject to change without notice.
-2-
REV. 0
ADF4001 TIMING CHARACTERISTICS (AV
Parameter t1 t2 t3 t4 t5 t6
10%, 5 V DD = DVDD = 3 V 4.7 k ; TA = TMIN to TMAX unless otherwise noted; dBm referred to 50 .)
Limit at TMIN to TMAX (B Version) 10 10 25 25 10 20
10%; AVDD VP 6.0 V ; AGND = DGND = CPGND= 0 V; RSET =
Unit ns min ns min ns min ns min ns min ns min
Test Conditions/Comments DATA to CLOCK Set Up Time DATA to CLOCK Hold Time CLOCK High Duration CLOCK Low Duration CLOCK to LE Set Up Time LE Pulsewidth
NOTES Guaranteed by design but not production tested. Specifications subject to change without notice.
t3
CLOCK
t4
t1
DATA DB20 (MSB) DB19
t2
DB2 DB1 (CONTROL BIT C2) DB0 (LSB) (CONTROL BIT C1)
t6
LE
t5
LE
Figure 1. Timing Diagram
ABSOLUTE MAXIMUM RATINGS 1, 2
(TA = 25C unless otherwise noted) AVDD to GND3 . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +7 V AVDD to DVDD . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to + 0.3 V VP to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +7 V VP to AVDD . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +5.5 V Digital I/O Voltage to GND . . . . . . . . . -0.3 V to VDD + 0.3 V Analog I/O Voltage to GND . . . . . . . . . . -0.3 V to VP + 0.3 V REFIN, RFINA, RFINB to GND . . . . . . . -0.3 V to VDD + 0.3 V RFINA to RFINB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320 mV Operating Temperature Range Industrial (B Version) . . . . . . . . . . . . . . . . -40C to +85C Storage Temperature Range . . . . . . . . . . . . -65C to +150C Maximum Junction Temperature . . . . . . . . . . . . . . . . . . 150C
TSSOP JA Thermal Impedance . . . . . . . . . . . . . . 150.4C/W CSP JA Thermal Impedance (Paddle Soldered) . . . . 122C/W CSP JA Thermal Impedance (Paddle Not Soldered) . . 216C/W Lead Temperature, Soldering Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . 215C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220C
NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 This device is a high-performance RF integrated circuit with an ESD rating of < 2 k and it is ESD sensitive. Proper precautions should be taken for handling and assembly. 3 GND = AGND = DGND = 0 V.
ORDERING GUIDE
Model ADF4001BRU ADF4001BCP
Temperature Range -40C to +85C -40C to +85C
Package Description Thin Shrink Small Outline Package (TSSOP) Chip Scale Package*
Package Option RU-16 CP-20
*Contact factory for chip availability.
CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADF4001 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. 0
-3-
ADF4001
PIN FUNCTION DESCRIPTIONS
Pin 1
Mnemonic RSET
Function Connecting a resistor between this pin and CPGND sets the maximum charge pump output current. The nominal voltage potential at the RSET pin is 0.66 V. The relationship between ICP and RSET is
I CP MAX = 23.5 RSET
2 3 4 5 6 7 8
CP CPGND AGND RFINB RFINA AVDD REFIN
9 10 11 12 13 14 15 16
DGND CE CLK DATA LE MUXOUT DVDD VP
So, with RSET = 4.7 k, ICP MAX = 5 mA. Charge Pump Output. When enabled, this provides ICP to the external loop filter which, in turn, drives the external VCO or VCXO. Charge Pump Ground. This is the ground return path for the charge pump. Analog Ground. This is the ground return path of the prescaler. Complementary Input to the N Counter. This point must be decoupled to the ground plane with a small bypass capacitor, typically 100 pF. See Figure 3. Input to the N Counter. This small signal input is ac-coupled to the external VCO or VCXO. Analog Power Supply. This may range from 2.7 V to 5.5 V. Decoupling capacitors to the analog ground plane should be placed as close as possible to this pin. AVDD must be the same value as DVDD. Reference Input. This is a CMOS input with a nominal threshold of VDD/2 and a dc equivalent input resistance of 100 k. See Figure 2. This input can be driven from a TTL or CMOS crystal oscillator or can be ac-coupled. Digital Ground Chip Enable. A logic low on this pin powers down the device and puts the charge pump output into threestate mode. Taking the pin high will power up the device, depending on the status of the power-down bit F2. Serial Clock Input. This serial clock is used to clock in the serial data to the registers. The data is latched into the 24-bit shift register on the CLK rising edge. This input is a high-impedance CMOS input. Serial Data Input. The serial data is loaded MSB first with the two LSBs being the control bits. This input is a high-impedance CMOS input. Load Enable, CMOS Input. When LE goes high, the data stored in the shift registers is loaded into one of the four latches, the latch being selected using the control bits. This multiplexer output allows either the Lock Detect, the scaled RF, or the scaled Reference Frequency to be accessed externally. Digital Power Supply. This may range from 2.7 V to 5.5 V. Decoupling capacitors to the digital ground plane should be placed as close as possible to this pin. DVDD must be the same value as AVDD. Charge Pump Power Supply. This should be greater than or equal to VDD. In systems where VDD is 3 V, it can be set to 5 V and used to drive a VCO or VCXO with a tuning range of up to 5 V.
PIN CONFIGURATIONS
20 CP 19 RSET 18 VP 17 DVDD 16 DVDD
CPGND 1 AGND 2 AGND 3 RFINB 4 RFINA 5
PIN 1 INDICATOR
RSET 1 CP 2 CPGND 3 AGND 4
16 VP 15 DVDD
ADF4001
14 MUXOUT 13 LE
TOP VIEW RFINB 5 (Not to Scale) 12 DATA RFINA 6 AVDD 7 REFIN 8 11 CLK 10 CE 9 DGND
ADF4001
TOP VIEW
15 MUXOUT 14 LE 13 DATA 12 CLK 11 CE
TRANSISTOR COUNT
6425 (CMOS) and 50 (Bipolar).
-4-
AVDD 6 AVDD 7 REFIN 8 DGND 9 DGND 10
REV. 0
Typical Performance Characteristics-ADF4001
0 -5
10dB/DIVISION -40 -50 -60
RL = -40dBc/Hz
rms NOISE = 0.229 DEGREES 0.229 rms
-10
AMPLITUDE - dBm
PHASE NOISE - dBc/Hz
-70 -80 -90 -100 -110 -120
-15 TA = +85 C -20 TA = +25 C -25 -30 TA = -40 C -35 0 50 100 150 FREQUENCY - MHz 200 250
-130 -140 100
1k 10k 100k FREQUENCY OFFSET FROM 200MHz CARRIER - Hz
1M
TPC 1. Input Sensitivity. VDD = 3.3 V; 100 pF on RFIN
TPC 4. Integrated Phase Noise (200 MHz, 200 kHz, 20 kHz)
0
0 -10 VDD = 3V, VP = 5V ICP = 2.5mA PFD FREQUENCY = 200kHz LOOP BANDWIDTH = 20kHz RES. BANDWIDTH = 300Hz VIDEO BANDWIDTH = 300Hz SWEEP = 4.2 SECONDS AVERAGES = 20
-5
OUTPUT POWER - dB
-20 -30 -40 -50 -60 -70 -80 -90
REFERENCE LEVEL = -5.7dBm
AMPLITUDE - dBm
-10
-15
-20
-92.3dBc
-25
-30 0 5 10 15 FREQUENCY - MHz 20 25
-100 -200kHz -100kHz 200MHz 100kHz 200kHz 0
TPC 2. Input Sensitivity. VDD = 3.3 V; 100 pF on RFIN
TPC 5. Reference Spurs (200 MHz, 200 kHz, 20 kHz)
0 -10 -20
OUTPUT POWER - dB
REFERENCE LEVEL = -5.7dBm
-30 -40 -50 -60 -70
VDD = 3V, VP = 5V ICP = 2.5mA PFD FREQUENCY = 200kHz LOOP BANDWIDTH = 20kHz RES. BANDWIDTH = 10Hz VIDEO BANDWIDTH = 10Hz SWEEP = 1.9 SECONDS AVERAGES = 26
-99.2dBc/Hz -80 -90 -100 -2kHz -1kHz 200MHz 1kHz 2kHz 0
TPC 3. Phase Noise (200 MHz, 200 kHz, 20 kHz)
REV. 0
-5-
ADF4001
CIRCUIT DESCRIPTION Reference Input Section
FROM N COUNTER LATCH
The reference input stage is shown in Figure 2. SW1 and SW2 are normally closed switches. SW3 is normally open. When power-down is initiated, SW3 is closed and SW1 and SW2 are opened. This ensures that there is no loading of the REFIN pin on power-down.
POWER-DOWN CONTROL
FROM RF INPUT STAGE
13-BIT N COUNTER
TO PFD
Figure 4. N Counter
R Counter
The 14-bit R counter allows the input reference frequency to be divided down to produce the reference clock to the phase frequency detector (PFD). Division ratios from 1 to 16,383 are allowed.
100k SW2 TO R COUNTER
NC
PHASE FREQUENCY DETECTOR (PFD) AND CHARGE PUMP
BUFFER
REFIN
NC SW1 SW3 NO
Figure 2. Reference Input Stage
RF Input Stage
The PFD takes inputs from the R counter and N counter and produces an output proportional to the phase and frequency difference between them. Figure 5 is a simplified schematic. The PFD includes a programmable delay element which controls the width of the antibacklash pulse. This pulse ensures that there is no deadzone in the PFD transfer function and minimizes phase noise and reference spurs. Two bits in the Reference Counter Latch, ABP2 and ABP1 control the width of the pulse. See Table III.
VP UP CHARGE PUMP
The RF input stage is shown in Figure 3. It is followed by a two-stage limiting amplifier to generate the CML clock levels needed for the N Counter buffer.
HI
BIAS GENERATOR 1.6V
D1
Q1
U1 R DIVIDER
AVDD
CLR1
2k
2k
DELAY
U3
CP
RFINA
RFINB
CLR2 HI N DIVIDER
AGND
D2
Q2 U2
DOWN
CPGND
Figure 3. RF Input Stage
N Counter
The N CMOS counter allows a wide ranging division ratio in the PLL feedback counter. Division ratios of 1 to 8191 are allowed.
N and R Relationship
R DIVIDER
N DIVIDER
The N counter, in conjunction with the R Counter make it possible to generate output frequencies that are spaced only by the Reference Frequency divided by R. The equation for the VCO frequency is as follows: fVCO = N/R x fREFIN fVCO N R Output Frequency of external voltage-controlled oscillator (VCO). Preset Divide Ratio of binary 13-bit counter (1 to 8,191). Preset divide ratio of binary 14-bit programmable reference counter (1 to 16,383). -6-
CP OUTPUT
Figure 5. PFD Simplified Schematic and Timing (In Lock)
MUXOUT AND LOCK DETECT
fREFIN External reference frequency oscillator.
The output multiplexer on the ADF4110 family allows the user to access various internal points on the chip. The state of MUXOUT is controlled by M3, M2, and M1 in the Function Latch. Table V shows the full truth table. Figure 6 shows the MUXOUT section in block diagram form.
REV. 0
ADF4001
DVDD
25 ns is detected on any subsequent PD cycle. The N-channel open-drain analog lock detect should be operated with an external pull-up resistor of 10 k nominal. When lock has been detected, this output will be high with narrow low-going pulses.
INPUT SHIFT REGISTER
ANALOG LOCK DETECT DIGITAL LOCK DETECT MUX R COUNTER OUTPUT CONTROL MUXOUT
N COUNTER OUTPUT
SDOUT
DGND
Figure 6. MUXOUT Circuit
Lock Detect
The ADF4001 digital section includes a 24-bit input shift register, a 14-bit R counter, and a 13-bit N counter. Data is clocked into the 24-bit shift register on each rising edge of CLK. The data is clocked in MSB first. Data is transferred from the shift register to one of four latches on the rising edge of LE. The destination latch is determined by the state of the two control bits (C2, C1) in the shift register. These are the two LSBs DB1, DB0 as shown in the timing diagram of Figure 1. The truth table for these bits is shown in Table I. Table II shows a summary of how the latches are programmed.
Table I. C2, C1 Truth Table
MUXOUT can be programmed for two types of lock detect: digital lock detect and analog lock detect. Digital lock detect is active high. When LDP in the R counter latch is set to "0," digital lock detect is set high when the phase error on three consecutive Phase Detector cycles is less than 15 ns. With LDP set to "1," five consecutive cycles of less than 15 ns are required to set the lock detect. It will stay set high until a phase error of greater than
Control Bits C2 C1 0 0 1 1 0 1 0 1
Data Latch R Counter N Counter Function Latch Initialization Latch
Table II. ADF4001 Family Latch Summary REFERENCE COUNTER LATCH
LOCK DETECT PRECISION
RESERVED
TEST MODE BITS DB19 T2 DB18 T1
ANTIBACKLASH WIDTH
14-BIT REFERENCE COUNTER
CONTROL BITS
DB23 DB22 X X
DB21 X
DB20 LDP
DB17 ABP2
DB16 ABP1
DB15 R14
DB14 R13
DB13 R12
DB12 R11
DB11 R10
DB10 R9
DB9 R8
DB8 R7
DB7 R6
DB6 R5
DB5 R4
DB4 R3
DB3 R2
DB2 R1
DB1
DB0
C2 (0) C1 (0)
N -COUNTER
RESERVED CP GAIN 13-BIT N COUNTER RESERVED CONTROL BITS
DB23 DB22 X X
DB21 G1
DB20 N13
DB19 N12
DB18 N11
DB17 N10
DB16 N9
DB15 N8
DB14 N7
DB13 N6
DB12 N5
DB11 N4
DB10 N3
DB9 N2
DB8 N1
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
C2 (0) C1 (1)
FUNCTION LATCH
FASTLOCK MODE PHASE DETECTOR POLARITY FASTLOCK ENABLE
RESERVED
CURRENT SETTING 2
CURRENT SETTING 1
TIMER COUNTER CONTROL
MUXOUT CONTROL
COUNTER RESET
POWERDOWN 2
POWERDOWN 1
CP THREESTATE
CONTROL BITS
DB23 DB22 X X
DB21 PD2
DB20 CPI6
DB19 CPI5
DB18 CPI4
DB17 CPI3
DB16 CPI2
DB15 CPI1
DB14 TC4
DB13 TC3
DB12 TC2
DB11 TC1
DB10 F5
DB9 F4
DB8 F3
DB7 F2
DB6 M3
DB5 M2
DB4 M1
DB3 PD1
DB2 F1
DB1
DB0
C2 (1) C1 (0)
INITIALIZATION LATCH
FASTLOCK MODE PHASE DETECTOR POLARITY FASTLOCK ENABLE
RESERVED
CURRENT SETTING 2
CURRENT SETTING 1
TIMER COUNTER CONTROL
MUXOUT CONTROL
COUNTER RESET
POWERDOWN 2
POWERDOWN 1
CP THREESTATE
CONTROL BITS
DB23 DB22 X X
DB21 PD2
DB20 CPI6
DB19 CPI5
DB18 CPI4
DB17 CPI3
DB16 CPI2
DB15 CPI1
DB14 TC4
DB13 TC3
DB12 TC2
DB11 TC1
DB10 F5
DB9 F4
DB8 F3
DB7 F2
DB6 M3
DB5 M2
DB4 M1
DB3 PD1
DB2 F1
DB1
DB0
C2 (1) C1 (1)
X = DON'T CARE
REV. 0
-7-
ADF4001
Table III. Reference Counter Latch Map
LOCK DETECT PRECISION
RESERVED
TEST MODE BITS DB19 T2 DB18 T1
ANTIBACKLASH WIDTH
14-BIT REFERENCE COUNTER
CONTROL BITS
DB23 DB22 X X
DB21 X
DB20 LDP
DB17 ABP2
DB16 ABP1
DB15 R14
DB14 R13
DB13 R12
DB12 R11
DB11 R10
DB10 R9
DB9 R8
DB8 R7
DB7 R6
DB6 R5
DB5 R4
DB4 R3
DB3 R2
DB2 R1
DB1
DB0
C2 (0) C1 (0)
X = DON'T CARE
R14 0 0 0 0 . . . 1 1 1 1
R13 0 0 0 0 . . . 1 1 1 1
R12 0 0 0 0 . . . 1 1 1 1
.......... .......... .......... .......... .......... .......... .......... .......... .......... .......... .......... ..........
R3 0 0 0 1 . . . 1 1 1 1
R2 0 1 1 0 . . . 0 0 1 1
R1 1 0 1 0 . . . 0 1 0 1
DIVIDE RATIO 1 2 3 4 . . . 16380 16381 16382 16383
ABP2 0 0 1 1
ABP1 0 1 0 1
ANTIBACKLASH PULSEWIDTH 2.9ns 1.3ns 6.0ns 2.9ns
TEST MODE BITS SHOULD BE SET TO 00 FOR NORMAL OPERATION
LDP 0 1
OPERATION THREE CONSECUTIVE CYCLES OF PHASE DELAY LESS THAN 15ns MUST OCCUR BEFORE LOCK DETECT IS SET. FIVE CONSECUTIVE CYCLES OF PHASE DELAY LESS THAN 15ns MUST OCCUR BEFORE LOCK DETECT IS SET.
-8-
REV. 0
ADF4001
Table IV. N Counter Latch Map
CP GAIN
RESERVED
13-BIT N COUNTER
RESERVED
CONTROL BITS
DB23 DB22 X X
DB21 G1
DB20 N13
DB19 N12
DB18 N11
DB17 N10
DB16 N9
DB15 N8
DB14 N7
DB13 N6
DB12 N5
DB11 N4
DB10 N3
DB9 N2
DB8 N1
DB7 X
DB6 X
DB5 X
DB4 X
DB3 X
DB2 X
DB1 C2 (0)
DB0 C1 (1)
X = DON'T CARE
N13 0 0 0 0 . . . 1 1 1 1
N12 0 0 0 0 . . . 1 1 1 1
N11 0 0 0 0 . . . 1 1 1 1 .......... .......... .......... .......... .......... .......... .......... .......... .......... .......... ..........
N3 0 0 0 1 . . . 1 1 1 1
N2 0 1 1 0 . . . 0 0 1 1
N1 1 0 1 0 . . . 0 1 0 1
N COUNTER DIVIDE RATIO 1 2 3 4 . . . 8188 8189 8190 8191
F4 (FUNCTION LATCH) FASTLOCK ENABLE CP GAIN 0 0 1 1 0 1 0 1
OPERATION CHARGE PUMP CURRENT SETTING 1 IS PERMANENTLY USED CHARGE PUMP CURRENT SETTING 2 IS PERMANENTLY USED CHARGE PUMP CURRENT SETTING 1 IS USED CHARGE PUMP CURRENT IS SWITCHED TO SETTING 2. THE TIME SPENT IN SETTING 2 IS DEPENDENT ON WHICH FASTLOCK MODE IS USED. SEE FUNCTION LATCH DESCRIPTION.
THESE BITS ARE NOT USED BY THE DEVICE AND ARE DON'T CARE BITS.
REV. 0
-9-
ADF4001
Table V. Function Latch Map
PHASE DETECTOR POLARITY FASTLOCK MODE FASTLOCK ENABLE
RESERVED
CURRENT SETTING 2
CURRENT SETTING 1
TIMER COUNTER CONTROL
MUXOUT CONTROL
COUNTER RESET
POWERDOWN 2
POWERDOWN 1
CP THREESTATE
CONTROL BITS
DB23 DB22 X X
DB21 PD2
DB20 CPI6
DB19 CPI5
DB18 CPI4
DB17 CPI3
DB16 CPI2
DB15 CPI1
DB14 TC4
DB13 TC3
DB12 TC2
DB11 TC1
DB10 F5
DB9 F4
DB8 F3
DB7 F2
DB6 M3
DB5 M2
DB4 M1
DB3 PD1
DB2 F1
DB1
DB0
C2 (1) C1 (0)
X = DON'T CARE
F2 0 1
PHASE DETECTOR POLARITY NEGATIVE POSITIVE
F1 0 1
COUNTER OPERATION NORMAL R, N COUNTER HELD IN RESET
F3 0 1
CHARGE PUMP OUTPUT NORMAL THREE-STATE
F4 0 1 1
F5 X 0 1
FASTLOCK MODE FASTLOCK DISABLED FASTLOCK MODE 1 FASTLOCK MODE 2
TC4 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
TC3 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
TC2 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
TC1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
TIMEOUT (PFD CYCLES) 3 7 11 15 19 23 27 31 35 39 43 47 51 55 59 63
M3 0 0 0 0 1 1 1 1
M2 0 0 1 1 0 0 1 1
M1 0 1 0 1 0 1 0 1
OUTPUT THREE-STATE OUTPUT DIGITAL LOCK DETECT N DIVIDER OUTPUT AVDD R DIVIDER OUTPUT N-CHANNEL OPEN-DRAIN LOCK DETECT SERIAL DATA OUTPUT DGND
CPI6 CPI3 0 0 0 0 1 1 1 1
CPI5 CPI2 0 0 1 1 0 0 1 1
CP14 CPI1 0 1 0 1 0 1 0 1 2.7k 1.088 2.176 3.264 4.352 5.44 6.528 7.616 8.704
ICP (mA) 4.7k 0.625 1.25 1.875 2.5 3.125 3.75 4.375 5.0 10k 0.294 0.588 0.882 1.176 1.47 1.764 2.058 2.352
CE PIN 0 1 1 1
PD2 X X 0 1
PD1 X 0 1 1
MODE ASYNCHRONOUS POWER-DOWN NORMAL OPERATION ASYNCHRONOUS POWER-DOWN SYNCHRONOUS POWER-DOWN
-10-
REV. 0
ADF4001
Table VI. Initialization Latch Map
FASTLOCK MODE PHASE DETECTOR POLARITY FASTLOCK ENABLE
RESERVED
CURRENT SETTING 2
CURRENT SETTING 1
TIMER COUNTER CONTROL
MUXOUT CONTROL
COUNTER RESET
POWERDOWN 2
POWERDOWN 1
CP THREESTATE
CONTROL BITS
DB23 DB22 X X
DB21 PD2
DB20 CPI6
DB19 CPI5
DB18 CPI4
DB17 CPI3
DB16 CPI2
DB15 CPI1
DB14 TC4
DB13 TC3
DB12 TC2
DB11 TC1
DB10 F5
DB9 F4
DB8 F3
DB7 F2
DB6 M3
DB5 M2
DB4 M1
DB3 PD1
DB2 F1
DB1
DB0
C2 (1) C1 (0)
X = DON'T CARE
F2 0 1
PHASE DETECTOR POLARITY NEGATIVE POSITIVE
F1 0 1
COUNTER OPERATION NORMAL R, N COUNTER HELD IN RESET
F3 0 1
CHARGE PUMP OUTPUT NORMAL THREE-STATE
F4 0 1 1
F5 X 0 1
FASTLOCK MODE FASTLOCK DISABLED FASTLOCK MODE 1 FASTLOCK MODE 2
TC4 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
TC3 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
TC2 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
TC1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
TIMEOUT (PFD CYCLES) 3 7 11 15 19 23 27 31 35 39 43 47 51 55 59 63
M3 0 0 0 0 1 1 1 1
M2 0 0 1 1 0 0 1 1
M1 0 1 0 1 0 1 0 1
OUTPUT THREE-STATE OUTPUT DIGITAL LOCK DETECT N DIVIDER OUTPUT AVDD R DIVIDER OUTPUT N-CHANNEL OPEN-DRAIN LOCK DETECT SERIAL DATA OUTPUT DGND
CPI6 CPI3 0 0 0 0 1 1 1 1
CPI5 CPI2 0 0 1 1 0 0 1 1
CP14 CPI1 0 1 0 1 0 1 0 1 2.7k 1.088 2.176 3.264 4.352 5.44 6.528 7.616 8.704
ICP (mA) 4.7k 0.625 1.25 1.875 2.5 3.125 3.75 4.375 5.0 10k 0.294 0.588 0.882 1.176 1.47 1.764 2.058 2.352
CE PIN 0 1 1 1
PD2 X X 0 1
PD1 X 0 1 1
MODE ASYNCHRONOUS POWER-DOWN NORMAL OPERATION ASYNCHRONOUS POWER-DOWN SYNCHRONOUS POWER-DOWN
REV. 0
-11-
ADF4001
THE FUNCTION LATCH
With C2, C1 set to 1, 0, the on-chip function latch will be programmed. Table V shows the input data format for programming the Function Latch.
Counter Reset
The device enters Fastlock by having a "1" written to the CP Gain bit in the N counter latch. The device exits Fastlock by having a "0" written to the CP Gain bit in the AB counter latch.
Fastlock Mode 2
DB2 (F1) is the counter reset bit. When this is "1," the R counter and the A, B counters are reset. For normal operation this bit should be "0." Upon powering up, the F1 bit needs to be disabled, the N counter resumes counting in "close" alignment with the R counter. (The maximum error is one prescaler cycle.)
Power-Down
The charge pump current is switched to the contents of Current Setting 2. The device enters Fastlock by having a "1" written to the CP Gain bit in the N counter latch. The device exits Fastlock under the control of the Timer Counter. After the timeout period determined by the value in TC4-TC1, the CP Gain bit in the N counter latch is automatically reset to "0" and the device reverts to normal mode instead of Fastlock. See Table V for the timeout periods.
Timer Counter Control
DB3 (PD1) and DB21 (PD2) on the ADF4110 Family, provide programmable power-down modes. They are enabled by the CE pin. When the CE pin is low, the device is immediately disabled regardless of the states of PD2, PD1. In the programmed asynchronous power-down, the device powers down immediately after latching a "1" into bit PD1, with the condition that PD2 has been loaded with a "0." In the programmed synchronous power-down, the device powerdown is gated by the charge pump to prevent unwanted frequency jumps. Once the power-down is enabled by writing a "1" into bit PD1 (on condition that a "1" has also been loaded to PD2), the device will go into power-down on the occurrence of the next charge pump event. When a power-down is activated (either synchronous or asynchronous mode, including CE-pin-activated power-down), the following events occur: All active dc current paths are removed. The R, N, and timeout counters are forced to their load state conditions. The charge pump is forced into three-state mode. The digital clock detect circuitry is reset. The RFIN input is debiased. The reference input buffer circuitry is disabled. The input register remains active and capable of loading and latching data.
MUXOUT Control
The user has the option of programming two charge pump currents. The intent is that the Current Setting 1 is used when the RF output is stable and the system is in a static state. Current Setting 2 is meant to be used when the system is dynamic and in a state of change (i.e., when a new output frequency is programmed). The normal sequence of events is as follows: The user initially decides what the preferred charge pump currents are going to be. For example, they may choose 2.5 mA as Current Setting 1 and 5 mA as Current Setting 2. At the same time they must also decide how long they want the secondary current to stay active before reverting to the primary current. This is controlled by the Timer Counter Control Bits DB14 to DB11 (TC4-TC1) in the Function Latch. The truth table is given in Table V. Now, when the user wishes to program a new output frequency, they can simply program the N counter latch with new value for N. At the same time they can set the CP Gain bit to a "1," which sets the charge pump with the value in CPI6-CPI4 for a period of time determined by TC4-TC1. When this time is up, the charge pump current reverts to the value set by CPI3-CPI1. At the same time the CP Gain bit in the N Counter latch is reset to 0 and is now ready for the next time that the user wishes to change the frequency. Note that there is an enable feature on the Timer Counter. It is enabled when Fastlock Mode 2 is chosen by setting the Fastlock Mode bit (DB10) in the Function Latch to "1."
Charge Pump Currents
The on-chip multiplexer is controlled by M3, M2, M1 on the ADF4001. Table V shows the truth table.
Fastlock Enable Bit
DB9 of the Function Latch is the Fastlock Enable Bit. Only when this is "1" is Fastlock enabled.
Fastlock Mode Bit
CPI3, CPI2, CPI1 program Current Setting 1 for the charge pump. CPI6, CPI5, CPI4 program Current Setting 2 for the charge pump. The truth table is given in Table V.
PD Polarity
DB10 of the Function Latch is the Fastlock Mode bit. When Fastlock is enabled, this bit determines which Fastlock Mode is used. If the Fastlock Mode bit is "0," Fastlock Mode 1 is selected; if the Fastlock Mode bit is "1, "Fastlock Mode 2 is selected.
Fastlock Mode 1
This bit sets the PD Polarity Bit. See Table V.
CP 3-State
This bit sets the CP output pin. With the bit set high, the CP output is put into three-state. With the bit set low, the CP output is enabled.
The charge pump current is switched to the contents of Current Setting 2.
-12-
REV. 0
ADF4001
THE INITIALIZATION LATCH The Counter Reset Method
When C2, C1 = 1, 1, the Initialization Latch is programmed. This is essentially the same as the Function Latch (programmed when C2, C1 = 1, 0). However, when the Initialization Latch is programmed, there is an additional internal reset pulse applied to the R and N counters. This pulse ensures that the N counter is at load point when the N counter data is latched, and the device will begin counting in close phase alignment. If the Latch is programmed for synchronous power-down (CE pin is High; PD1 bit is High; PD2 bit is Low), the internal pulse also triggers this power-down. The oscillator input buffer is unaffected by the internal reset pulse, and so close phase alignment is maintained when counting resumes. When the first N counter data is latched after initialization, the internal reset pulse is again activated. However, successive N counter loads after this will not trigger the internal reset pulse.
DEVICE PROGRAMMING AFTER INITIAL POWER-UP
Apply VDD. Do a Function Latch Load ("10" in 2 LSBs). As part of this, load "1" to the F1 bit. This enables the counter reset. Do an R Counter Load ("00" in 2 LSBs). Do an N Counter Load ("01" in 2 LSBs). Do a Function Latch Load ("10" in 2 LSBs). As part of this, load "0" to the F1 bit. This disables the counter reset. This sequence provides the same close alignment as the initialization method. It offers direct control over the internal reset. Note that counter reset holds the counters at load point and three-states the charge pump, but does not trigger synchronous power-down. The counter reset method requires an extra function latch load compared to the initialization latch method.
APPLICATIONS SECTION Extremely Stable, Low Jitter Reference Clock for GSM Base Station Transmitter
After initially powering up the device, there are three ways to program the device.
Initialization Latch Method
Figure 7 shows the ADF4001 being used with a VCXO to produce an extremely stable, low jitter reference clock for a GSM base station Local Oscillator (LO).
13MHz SYSTEM CLOCK
Apply VDD. Program the Initialization Latch ("11" in 2 LSBs of input word). Make sure that F1 bit is programmed to "0." Then do an R load ("00" in 2 LSBs). Then do an N load ("01" in 2 LSBs). When the Initialization Latch is loaded, the following occurs: 1. The function latch contents are loaded. 2. An internal pulse resets the R, N, and timeout counters to load state conditions and also three-states the charge pump. Note that the prescaler bandgap reference and the oscillator input buffer are unaffected by the internal reset pulse, allowing close phase alignment when counting resumes. 3. Latching the first N counter data after the initialization word will activate the same internal reset pulse. Successive N loads will not trigger the internal reset pulse unless there is another initialization.
The CE Pin Method
1 13MHz R DIVIDER PFD 1 RFIN N DIVIDER CHARGE PUMP CP LOOP FILTER VCXO
ADF4001
REFIN CP ADF4110 ADF4111 ADF4112 ADF4113 RFINA
LOOP FILTER
VCO
RFIN
Figure 7. Low Jitter, Stable Clock Source for GSM Base Station Local Oscillator cct
Apply VDD. Bring CE low to put the device into power-down. This is an asynchronous power-down in that it happens immediately. Program the Function Latch (10). Program the R Counter Latch (00). Program the N Counter Latch (01). Bring CE high to take the device out of power-down. The R and AB counters will now resume counting in close alignment. Note that after CE goes high, a duration of 1 s may be required for the prescaler bandgap voltage and oscillator input buffer bias to reach steady state. CE can be used to power the device up and down in order to check for channel activity. The input register does not need to be reprogrammed each time the device is disabled and enabled as long as it has been programmed at least once after VDD was initially applied. REV. 0
The system reference signal is applied to the circuit at REFIN. Typical GSM systems would have a very stable OCXO as the clock source for the entire base station. However, distribution of this signal around the base station makes it susceptible to noise and spurious pickup. It is also open to pulling from the various loads it may need to drive. The charge pump output of the ADF4001 (Pin 2) drives the loop filter and the 13 MHz VCXO. The VCXO output is fed back to the RF input of the ADF4001 and also drives the reference (REFIN) for the LO. A T-circuit configuration provides 50 matching between the VCXO output, the LO REFIN, and the RFIN terminal of the ADF4001.
COHERENT CLOCK GENERATION
When testing A/D converters, it is often advantageous to use a coherent test system, that is a system that ensures a specific relationship between the A/D converter input signal and the A/D converter sample rate. Thus, when doing an FFT on this data, there is no longer any need to apply the window weighting -13-
ADF4001
function. Figure 8 shows how the ADF4001 can be used to handle all the possible combinations of input signal frequency and sampling rate. The first ADF4001 is phase locked to a VCO. The output of the VCO is also fed into the N divider of the second ADF4001. This results in both ADF4001's being coherent with the REFIN. Since the REFIN comes from the signal generator, the MUXOUT signal of the second ADF4001 is coherent with the FIN frequency to the ADC. This is used as FS, the sampling clock.
FIN SINE OUTPUT BRUEL & KJAER MODEL 1051 FS = (FIN N1)/(R1 N2) AIN A/D CONVERTER UNDER TEST
52MHz MASTER CLOCK 486 N2 REFIN R1 4 CPRF LOOP FILTER VCXO 13MHz 13MHz SYSTEM CLOCK FOR GSM
1 N1
RFIN
ADF4001
REFIN R2 1300 CPRF LOOP FILTER 19.44MHz SYSTEM CLOCK FOR WCDMA VCXO 19.44MHz
RFIN
SAMPLING CLOCK FS R1 CPRF RFIN LOOP FILTER VCO 100MHz
REFIN
ADF4001
R3 65 CPRF LOOP FILTER VCXO 19.2MHz 19.2MHz SYSTEM CLOCK FOR CDMA
SQUARE OUTPUT
REFIN
ADF4001
N1
24 N3
RFIN
N2
RFIN NC7S04 MUXOUT
ADF4001
Figure 9. Tri-Band System Clock Generation
VP
ADF4001
Figure 8. Coherent Clock Generator
POWER-DOWN CONTROL
TRI-BAND CLOCK GENERATION CIRCUIT
In multi-band applications, it is necessary to realize different clocks from one master clock frequency. For example, GSM uses a 13 MHz system clock, WCDMA uses 19.44 MHz, and CDMA uses 19.2 MHz. The circuit in Figure 9 shows how to use the ADF4001 to generate GSM, WCDMA, and CDMA system clocks from a single 52 MHz Master Clock. The low RF Fmin spec and the ability to program R and N values as low as 1 makes the ADF4001 suitable for this. Other FOUT clock frequencies can be realized using the formula: FOUT = REFIN ( N / R )
SHUTDOWN CIRCUIT
S VDD IN
VDD RFOUT
ADG702
D GND 100pF
7
15
16
10 CE CP 2 LOOP FILTER
AVDD DVDD VP
VCC 100pF 18 VCO OR VCXO GND
18
FREFIN
RSET
1 10k
18
ADF4001
The circuit in Figure 10 shows how to shut down both the ADF4001 and the accompanying VCO. The ADG702 switch goes open circuit when a Logic "1" is applied to the IN input. The low-cost switch is available in both SOT-23 and micro SO packages.
3 4
100pF RFINA 6 51 RFINB 5
CPGND AGND DGND 9
100pF DECOUPLING CAPACITORS AND INTERFACE SIGNALS HAVE BEEN OMITTED FROM THE DIAGRAM IN THE INTEREST OF GREATER CLARITY.
Figure 10. Local Oscillator Shutdown Circuit
-14-
REV. 0
ADF4001
INTERFACING ADSP-2181 Interface
The ADF4001 family has a simple SPI-compatible serial interface for writing to the device. SCLK, SDATA, and LE control the data transfer. When LE (Latch Enable) goes high, the 24 bits that have been clocked into the input register on each rising edge of SCLK will be transferred to the appropriate latch. See Figure 1 for the Timing Diagram and Table I for the Latch Truth Table. The maximum allowable serial clock rate is 20 MHz. This means that the maximum update rate possible for the device is 833 kHz or one update every 1.2 ms. This is certainly more than adequate for systems with typical lock times in hundreds of microseconds.
ADuC812 Interface
Figure 12 shows the interface between the ADF4001 family and the ADSP-21xx Digital Signal Processor. The ADF4001 family needs a 24-bit serial word for each latch write. The easiest way to accomplish this using the ADSP-21xx family is to use the Autobuffered Transmit Mode of operation with Alternate Framing. This provides a means for transmitting an entire block of serial data before an interrupt is generated. Set up the word length for 8 bits and use three memory locations for each 24-bit word. To program each 24-bit latch, store the three 8-bit bytes, enable the Autobuffered mode, and then write to the transmit register of the DSP. This last operation initiates the autobuffer transfer.
Figure 11 shows the interface between the ADF4001 family and the ADuC812 microconverter. Since the ADuC812 is based on an 8051 core, this interface can be used with any 8051-based microcontroller. The microconverter is set up for SPI Master Mode with CPHA = 0. To initiate the operation, the I/O port driving LE is brought low. Each latch of the ADF4001 family needs a 24-bit word. This is accomplished by writing three 8-bit bytes from the microconverter to the device. When the third byte has been written, the LE input should be brought high to complete the transfer. On first applying power to the ADF4001 family, it needs three writes (one each to the R counter latch, the N counter latch and the initialization latch) for the output to become active. I/O port lines on the ADuC812 are also used to control powerdown (CE input) and to detect lock (MUXOUT configured as lock detect and polled by the port input). When operating in the mode described, the maximum SCLOCK rate of the ADuC812 is 4 MHz. This means that the maximum rate at which the output frequency can be changed will be 166 kHz.
ADuC812
SCLOCK MOSI SCLK SDATA LE I/O PORTS CE MUXOUT (LOCK DETECT)
ADSP-21xx
SCLK DT TFS SCLK
ADF4001
SDATA LE CE
I/O FLAGS
MUXOUT (LOCK DETECT)
Figure 12. ADSP-21xx to ADF4001 Family Interface
PCB DESIGN GUIDELINES FOR CHIP SCALE PACKAGE
The lands on the chip package (CP-20) are rectangular. The printed circuit board pad for these should be 0.1 mm longer than the package land length and 0.05 mm wider than the package land width. The land should be centered on the pad. This will ensure that the solder joint size is maximized. The bottom of the chip scale package has a central thermal pad. The thermal pad on the printed circuit board should be at least as large as this exposed pad. On the printed circuit board, there should be a clearance of at least 0.25 mm between the thermal pad and the inner edge of the pad pattern. This will ensure that shorting is avoided. Thermal vias may be used on the printed circuit board thermal pad to improve thermal performance of the package. If vias are used, they should be incorporated in the thermal pad at 1.2 mm pitch grid. The via diameter should be between 0.3 mm and 0.33 mm and the via barrel should be plated with 1 oz. copper to plug the via. The user should connect the printed circuit board thermal pad to AGND.
ADF4001
Figure 11. ADuC812 to ADF4001 Family Interface
REV. 0
-15-
ADF4001
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
16-Lead Thin Shrink SO Package (TSSOP) (RU-16)
C02569-1-7/01(0)
8 0 0.028 (0.70) 0.020 (0.50)
0.010 (0.25) MIN
20 1
0.201 (5.10) 0.193 (4.90)
16
9
0.177 (4.50) 0.169 (4.30) 0.256 (6.50) 0.246 (6.25)
1 8
PIN 1 0.006 (0.15) 0.002 (0.05) 0.0433 (1.10) MAX
SEATING PLANE
0.0256 (0.65) 0.0118 (0.30) BSC 0.0075 (0.19)
0.0079 (0.20) 0.0035 (0.090)
20-Leadless Frame Chip Scale Package (LFCSP) (CP-20)
0.024 (0.60) 0.017 (0.42) 0.009 (0.24) 0.024 (0.60) 0.017 (0.42) 16 0.009 (0.24) 15 0.148 (3.75) BSC SQ 0.012 (0.30) 0.009 (0.23) 0.007 (0.18) 0.030 (0.75) 0.022 (0.60) 0.014 (0.50)
0.157 (4.0) BSC SQ
PIN 1 INDICATOR
TOP VIEW
BOTTOM VIEW
11 10 6 5
0.080 (2.25) 0.083 (2.10) SQ 0.077 (1.95)
12 MAX 0.035 (0.90) MAX 0.033 (0.85) NOM SEATING PLANE 0.020 (0.50) BSC
0.031 (0.80) MAX 0.026 (0.65) NOM
0.080 (2.00) REF
0.008 (0.20) REF
0.002 (0.05) 0.0004 (0.01) 0.0 (0.0)
CONTROLLING DIMENSIONS ARE IN MILLIMETERS
-16-
REV. 0
PRINTED IN U.S.A.

▲Up To Search▲

Price & Availability of ADF4001

	To Download ADF4001 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .